Mitsubishi Electronics Trim 110 User Manual

This guide describes the operation of the dual band GSM telephones

Trium 110.

Edition 1, 2002.

Whilst every effort has been made to ensure the accuracy of the instructions contained in this

guide, Mitsubishi Electric reserves the right to make improvements and changes to the product

described in this guide and/or to the guide itself, without prior notice.

developed by independent scientific or-

ganisations through periodic and thor-

ough evaluation of scientific studies. The

limits include a substantial safety margin

designed to assure the safety of all per-

sons, regardless of age and health.

Introduction

Thank you for purchasing the Trium 110

dual band mobile telephone. The phone

version you have bought is either the

Trium 110, the Trium 110 m or the Tri-

um 110 p. Please check the version on

the box label. The mobile telephone de-

scribed in this guide is approved for use

on all GSM 900/1800 networks. Some

services and messages may be different

according to your subscription type

and/or service provider.

The exposure standard for mobile

phones (CENELEC standard EN 50360:

2000) employs a unit of measurement

known as the Specific Absorption Rate,

or SAR. The SAR limit²recommended by

The Council of the European Union is

2.0 W/kg. Tests for SAR have been con-

ducted using standard operating posi-

tions (with reference to CENELEC

standard EN 50361: 2000) with the

phone transmitting at its highest certi-

fied power level in all tested frequency

bands³. Although the SAR is determined

at the highest certified power level, the

actual SAR level of the phone while op-

erating can be well below the maximum

value. This is because the phone is de-

signed to operate at multiple power lev-

els so as to use only the power required

to reach the network. In general, the

closer you are to a base station antenna,

the lower the power output.

As with all types of radio transceivers

this mobile telephone emits electro-

magnetic waves and conforms to inter-

national regulations when it is used

under normal conditions and in accord-

ance with the safety and warning mes-

sages given below and on page 4.

SAR

THIS TRIUM 110, TRIUM 110 m OR TRI-

UM 110 p PHONE MEETS THE EU RE-

QUIREMENTS FOR EXPOSURE TO RADIO

WAVES.

Before a mobile phone is available for

sale to the public, compliance with the

European R&TTE directive (1999/5/CE)

must be shown. This directive includes

as one essential requirement the pro-

tection of the health and the safety for

the user and any other person.

Your mobile phone is a radio transmitter

and receiver. It is designed and manufac-

tured not to exceed the limits for expo-

sure to radiofrequency (RF) energy

recommended by The Council of the Eu-

ropean Union¹. These limits are part of

comprehensive guidelines and establish

permitted levels of RF energy for the

general population. The guidelines were

The highest SAR value for this Trium

110, Trium 110 m or Trium 110 p model

when tested for compliance against the

standard was 0.746 W/kg. While there

may be differences between the SAR

levels of various phones and at various

positions, they all meet the EU require-

ments for RF exposure.

2. The SAR limit for mobile phones used by the

public is 2.0 watts/kilogram (W/kg) averaged

over ten grams of tissue. The limit incorpora-

tes a substantial margin of safety to give

additional protection for the public and to

account for any variations in measurements

3. The maximum level of GSM emitted power is

250mW at 900 MHz and 125 mW at

1. European recommendation 1999/519/CE

1800 MHz according to the GSM standard.

There are a number of independent

sources of information available to us-

ers including:

Switch off phone when at any

refuelling point or near inflam-

mable material.

Royal Society of Canada: www.rsc.ca

The International Commission on Non-

Ionizing Radiation Protection (ICNIRP):

www.icnirp.de

The US Food and Drug Administration:

www.fda.gov/cdrh/ocd/mobil-

phone.html

The World Health Organization:

www.who.int/emf

Mitsubishi Electric belongs to the MMF,

an international association of radio

equipment manufacturers.

The MMF produces information such as

this in accordance with its purpose of

developing and presenting industry po-

sitions to independent research organi-

sations, government and other research

bodies.

Mobile Manufacturers Forum

Diamant Building, 80 Blvd. A. Reyers

B-1030 Brussels Belgium

Switch off phone in hospitals

and any other place where med-

ical equipment may be in use.

Respect restrictions on the use

of radio equipment in fuel de-

pots, chemical plants or where

blasting operations are in

progress.

There may be a hazard associat-

ed with the operation of phones

close to inadequately protected

personal medical devices such as

hearing aids and pacemakers.

Consult your doctor or the man-

ufacturers of the medical device

to determine if it is adequately

protected.

Operation of phone close to oth-

er electronic equipment may

also cause interference if the

equipment is inadequately pro-

tected. Observe any warning

signs and manufacturers recom-

mendations.

www.mmfai.org

General safety

It is important to follow any special reg-

ulations regarding the use of radio

equipment, due to the possibility of ra-

dio frequency, interference.

Please follow the safety advice given be-

low.

Vehicle safety

Respect national regulations on the use

of mobile telephones in vehicles.

Road safety always comes first! Always

give your full attention to driving.

• Do not use a hand-held phone while

driving. If you do not have a ‘hands

free’ car kit, stop and park your vehi-

cle safely before using your phone.

• If equipped with a correctly installed

vehicle kit allowing ‘hands free’ oper-

ation and you need to make or

receive a call, ensure that it is done

sensibly and safely. Use pre-pro-

grammed numbers where possible

and keep calls short and routine.

Switch off phone and remove

the battery when in an aircraft.

The use of mobile telephones in

an aircraft may endanger the

operation of the aircraft, disrupt

the cellular mobile phone net-

work and is illegal. Failure to ob-

serve this instruction may lead

to suspension or denial of mo-

bile telephone services to the of-

fender, or legal action, or both.

• If incorrectly installed in a vehicle the

operation of mobile telephones can

interfere with the correct operation

of the vehicle electronics, such as

ABS anti-lock brakes or air bags. To

avoid such problems ensure that only

qualified personnel carry out the

installation. Verification of the pro-

tection and operation of the vehicle

electronics should form part of the

installation. If in doubt consult the

manufacturer.

• Do not place the phone on the pas-

senger seat or where it could break

loose during sudden breaking or a

collision. Always use the holder.

• The use of an alert device to operate

a vehicle's lights or horn on public

roads is not permitted.

Care and maintenance

This mobile telephone is the product of

advanced engineering, design and

craftsmanship and should be treated

with care. The suggestions below can

help you to enjoy this product for many

years.

• Do not expose the phone to any

extreme environment where the tem-

perature or humidity is high.

• Do not expose or store in cold tem-

peratures. When the phone warms up

after switch on, to its normal temper-

ature, moisture can form inside which

can damage the electrical parts.

• Do not attempt to disassemble the

phone. There are no user serviceable

parts inside.

• Do not expose the phone to water,

rain or spilt beverages. It is not

waterproof.

Emergency calls

In Europe, provided the phone has GSM

service, emergency calls can be made

using the European standard emergen-

cy number, 112, even if you do not

have a SIM in the phone. Emergency

calls can even be made if the phone is

PIN or electronically locked or call

barred. In some countries local emer-

gency numbers can still be used for

emergency purposes but the phone

may have to contain a valid SIM card.

When making an emergency call re-

member to give all the necessary infor-

mation as accurately as possible. The

phone may be the only means of com-

munication at the scene of an emergen-

cy therefore do not cut off the call until

• Do not abuse this phone by drop-

ping, knocking or violent shaking.

Rough handling can damage it.

• Do not clean the phone with strong

chemicals or solvents. Wipe it only

with a soft, slightly dampened cloth.

• Do not place the telephone alongside

computer discs, credit or travel cards

or other magnetic media. The infor-

mation contained on discs or cards

may be affected by the phone.

• Do not connect incompatible prod-

ucts. The use of third party equip-

ment or accessories, not made or

authorised by Mitsubishi Electric,

invalidates the warranty of your

phone and can be a safety risk.

told to do so.

• Do not remove the labels. The num-

bers on it are important for aftersale

service and other related purposes.

• Do contact an authorised service cen-

tre in the unlikely event of a fault.

Mobile phones rely on wireless and landline net-

works which cannot be guaranteed in all condi-

tions. Therefore you should never rely solely on

wireless phones for essential emergency commu-

nications.

Battery disposal

AC/DC adaptor chargers

In compliance with European environ-

mental protection directives, used

batteries must be returned to the

place of sale, where they are collected

free of charge.

This apparatus is intended for use only

when supplied with power from AC/DC

adaptor

FZ14130060,

FZ14130080,

chargers

(FZ14130070,

FZ14130050,

FZ14130090

Don't throw away your batteries in

your household waste.

FZ14130100). Use of any other charger

or adaptors will invalidate any approval

given to this apparatus and may be

dangerous.

Your responsibility

This GSM mobile telephone is your re-

sponsibility. Please treat it with care re-

specting all local regulations. It is not a

toy; please keep it in a safe place at all

times and out of the reach of children.

Become familiar with and use the secu-

rity features to block unauthorised use

if your phone and/or SIM card are lost

or stolen. Call your service provider im-

mediately to prevent illegal use.

Battery use

You can charge a battery hundreds of

times but gradually it wears out. When

the operating time (stand-by and talk

time) is noticeably shorter than normal

it is time to buy a new battery.

• Do not leave batteries connected to a

charger longer than necessary. Over-

charging shortens battery life.

• Disconnect battery chargers from the

power source when not in use.

• Do not expose batteries to high tem-

peratures or humidity.

• Do not dispose of the batteries in

fire. They can explode.

• Avoid putting the batteries into con-

tact with metal objects which can

short circuit the battery terminals

(e.g. keys, paper clips, coins, chains

etc.).

When not in use lock, turn off the

phone and remove the battery.

Security codes

The phone and SIM card are delivered

to you pre-programmed with codes

that protect the phone and SIM card

against unauthorised use. A short de-

scription of each follows. See page 36

to change your PIN and phonelock

codes.

• Do not drop or subject the batteries

to strong physical shocks.

• Do not try to disassemble any of the

battery packs.

PIN and PIN2 codes (4-8 digits)

All SIM cards have a PIN (Personal

Identity Number). It protects the

card against unauthorised use.

• Use only the recommended battery

chargers (see page 6).

• If the battery terminals become

soiled, clean them with a soft cloth.

• It is normal for batteries to become

warm during charging.

Some SIM cards also have a PIN2

code that protects specific features

such as fixed dialling numbers.

Entering the wrong PIN code three

times in succession disables the SIM

card and the message SIM Blocked.

Enter PUK: appears. To unblock the

SIM you need the PUK (PIN Unblock

Key) code, obtainable only from

your service provider.

PUK and PUK2 codes (8 digits)

Obtain the PUK code from your

service provider. Use it to unblock a

disabled SIM card (see page 37).

The PUK2 code is required to un-

block the PIN2 code (see above).

Call barring password (4 digits)

This password is used to bar various

types of calls, made or received,

from the phone (see page 42).

Phonelock code (4 digits)

This code is set to all zeros on deliv-

ery. You can change it. Once

changed it cannot be identified by

the manufacturer over the phone.

Please refer to page 36 for more de-

tails.

You must remember and make yourself

familiar with the purpose and operation

of these codes.

Disposing of waste packaging

The packaging used for this phone is

made of recyclable materials and as

such should be disposed of in accord-

ance with your national legislation on

the protection of the environment.

Please take care to separate the card-

board and plastic elements and to dis-

pose of them in the correct manner.

The phone at a glance

Earpiece

Programmable

Graphic display

Telephone

softkeys (

)

The function of

the softkey appears

in the graphic

numbers, menus,

messages, etc. are

displayed here.

display above the key.

Cursor key

Navigates

around the

memories and

On/Off, END key

). Hold down to

(

turn the phone on/off.

Press to end a call or

return to stand-by.

menus.

on the cursor

key: press to scroll

up menus (while in

the menu). In stand-by,

press to access the

volume control.

on the cursor key.

Press to scroll down

menus (while in the

menu). In stand-by,

press to access the

alert mode (ring, silent,

vibrate, etc.)

Alphanumeric keys,

To enter numbers,

characters and

punctuation marks.

Press and hold

call the voice mail

number. Press and

hold

dial preferred

numbers. Press and

hold to enter

keys to

on the cursor key.

Press to access the

main menu or select a

menu option.

international code +

prefix, 'P' symbol or '_'

underscore wildcard. .

Press and hold

activate the keypad

lock feature.

on the cursor key.

Press to access

the phone book or

return to the

Battery cover

(at the back of

the phone)

See page 10

for further

previous display.

Call/SEND key ( ).

Press to make/answer a

call. In stand-by, press

to display the last

details.

Microphone

Headset, accessories

and AC/DC charger

socket

dialled numbers list.

Graphic display

Arrow keys. Displayed during

menu operation to indicate that

more items in the menu can be

The display shows

icons,

alphabet

characters, num-

displayed if

are pressed.

bers, menu list

and instructions

to the user. Use

the cursor keys to navigate to the

phone book, Internet/WAP™ and the

menu. The rest of this guide gives you

the procedures to access these func-

tions. Icons in the display are described

on page 9.

Voice mail. Displayed when you

have a voice mail message to

read.

The availability of this feature is

network dependent.

Battery level indicator. Perma-

nently displayed to indicate the

current charge level of the bat-

tery. Three levels are shown.

Understanding the icons

low,

medium,

when the battery is almost

full. It flash-

Icons in the display have the following

meaning:

empty.

SIM memory in use

Line 2. Indicates the second line is

in use.

Phone memory in use.

The availability of this feature is

network dependent.

When you enter a name and ad-

dress you can choose the icon you

want to go with them.

Signal strength level. It indicates

the strength of the received sig-

nal. The more bars the stronger

the signal. If no network is availa-

ble the display remains blank.

Roaming. Displayed when the

phone is logged on to a network

different from its home network.

Short message service (SMS). Dis-

played when you have one or

See also page 33.

Sending DTMF tones

Hands free features

Some remote access services require

DTMF tones. These tones are used by

regular telephones when you dial and

when you answer questions from an

automated voice service. If you are in a

conversation and manually entering the

numbers, no extra configuration is nec-

essary. If, however, you want to send a

number stored in memory, you must set

DTMF to automatic.

When you want to share your call with

an audience, or you are in your car, use

the “hands free” feature.

Turning the hands free feature on

When making a call:

Press Speak.on

to turn the

hands free feature on during the

calling process.

When receiving a call:

Press Speak.on

incoming call.

to accept the

Manually

To send individual DTMF tones di-

rectly from the keypad during a

conversation:

Turning the hands free feature off

Press Speak.off

Press the required keys.

The tones are heard in the ear-

piece and sent immediately.

Automatically

To send a consecutive string of

To end either the current call

or the held call select End

active or End held in the

Options menu. The remain-

ing call is automatically

retrieved

DTMF tones during a conversation:

Press Options

Select Auto DTMF.

Enter the DTMF numbers into

the display either directly

using the keypad or from a

number stored in the phone

book (under Names ).

Press

call.

to end the remaining

Both calls can be ended at the same time by press-

ing

Alternatively, use Options

display a menu of the actions de-

scribed above. Scroll to the re-

quired option and press Select

or (see also Multi-party or con-

ference calls (network depend-

Press OK . The phone sends

the tones and then shows the

normal conversation display.

DTMF tones cannot be sent when a call is on hold.

Pause feature

ent),

page 19).Call

waiting,

You can enter and store telephone

numbers and a sequence of DTMF tones

together as long as you separate them

by a 'pause'. To enter a pause between

numbers, press and hold down . The

letter p appears. The phone can store

several pauses together for a maximum

of 20-46 characters (dependent upon

the SIM and the phone memory capaci-

ty).

swapping and multi-party confer-

ence calls

Call waiting (network dependent)

Use call waiting, a network feature,

to receive a second incoming call

when already engaged in a call. This

puts an existing call 'on hold' while

you answer or make a second call.

To turn the call waiting service on

or off:

Holding and retrieving a call

Press . Select Settings.

Select GSM Services.

To put a call on hold during a con-

versation:

Select Call waiting.

Select Activate or Cancel.

The network confirms your

request. The confirmation can

take several seconds.

Press

To retrieve a call:

Press

Press and hold Exit

To make a second call when one call

is on hold:

to return to the standby dis-

play.

Enter a number in the display.

Press

After the second call has been

established press to swap

between the two calls.

to dial the number.

Action when receiving a second call

You hear a 'double beep' when your

phone receives a second call. An an-

imated phone icon and the tele-

phone number (if available) also

appear.

To accept the second call

Press . This answers the second

call and puts the first call on hold.

Option

Auto

DTMF

Description

to enter a DTMF string

to the active call only

Swaps between active

and call on hold

Joins active and call on

hold to make a multi-

party or conference call

Turns on or off the mi-

Swap

Join

Mute/

Unmute crophone

End held Ends the call on hold

To reject the second call:

Press Reject . This returns a

busy signal to the second caller.

Ends the active call and

End ac-

To swap between the two connect-

ed calls:

connects with the call

tive

on hold

Press

End all

Ends all the calls

Allows you to select

and have a private con-

* Private versation with one of

Multi-party or conference calls (net-

work dependent)

Use this feature to make or receive

between 2 to 5 calls at the same

time with all parties being able to

hear and talk with each other.

with

the conference callers

while putting all the

other calls on hold

Hold/Re- Holds or retrieves the

Make and establish a call in

the normal way and press

trieve

conference call

Allows you to select

and end one of the

conference call partici-

pants

Enter another number into

the display and press . The

first call is put on hold when

the second call becomes

active.

* End one

* These items in the Options menu

appear if more than 2 calls are

joined in the conference call.

Throughout the conference call the

display shows the actions you se-

lected from the options menu.

For alternate line service (ALS), you cannot make

subscribers conference calls between Line 1 and

Line 2.

Press Options

lowing menu:

for the fol-

The menu

Recall

Store

Use the round cursor key to access the

menu system. Your menu options can

vary. Some may not appear. This de-

pends on your network operator and

your subscription, plus on the phone

version you have (check on box label).

Remaining

Own numbers

Fixed dialling

Phone Book tones

Phone Book

SMS*

Inbox

Outbox

Access to the menus

Write new

Settings

Press

to view all stored telephone

Draft texts

Alert

numbers.

Press to enter the main menu.

Hold down Exit

the menus (if no call is in progress).

Messages

Storage

EMS*

or press

to exit

Inbox*

My Services*

Settings*

Service Registration*

Menu map

Calls log

Internet

Calls & Times

Settings

Call timers

Phone settings

Voice mail

GSM Services

Broadcast

Network

Server

Currency

Games

Scratchpad

Alarm clock

Auto-switch

Calculator

Office Tools

Phone Book

Messages

Reshape

Push

Office Tools

Games

Options

Exen Games**

Currency

Settings

Items in italics depend on your sub-

scription and your network operator.

* Available on Trium 110 m only

** Available on Trium 110 p only

Settings

Calls & Times

Sub-menu

Entering text

Home page

Inbox

To add names to the phone books (see

page 22) and write text messages (see

page 26) you must enter text. The

Bookmarks

Other site

Profile list

Settings

Internet

phone displays

in lower case mode

and in upper case mode when you

can enter text. Use the keypad to enter/

edit text.

Push parameters

Network

Server

Information

Services

You can enter text/numbers using T9

text entry or Multitap text entry.Press

to swap between T9 text entry and the

Multitap method.

• Select Write new.

• Press appears.

• Press . A appears.

To enter text with T9:

• Press . Ca appears.

• Press . Car appears.

• Press . Case appears.

If the displayed word is not the

Press the key with the re-

quired letter only once.

Do not be put off if the char-

acter you want is not immedi-

ately displayed.

one you want, press

as many

times as necessary to view Card.

The ‘active’ word changes as

you type, so type to the end

of the word.

• Press

to exit from this example

and return to the stand-by display.

If your word is not displayed,

Multitap text entry

press

words.

for other matching

Press on to swap between T9 text

entry and the Multitap method.

To enter text with multitap:

If your word is not recog-

nised, press to swap to the

Multitap method to complete

the word.

Press the key with the

required letter. If it is not the

first letter, press key repeat-

edly until the letter appears.

See the table that follows for

a key to character corre-

spondence.

Use or to locate the cur-

sor in the text to insert char-

acters or make corrections.

1. T9 may not be available in all languages.

2. During number and name entry a short press on

Clear deletes the last character. A long press clears

the whole display.

Enter the next character. If

two characters are on the

same key, wait for the display

at the top of the screen to

clear or press before press-

ing the same key again.

Tips and operation

Key

Action

Shift - upper/lower

case on next letter.

Caps lock/unlock if

you press and hold it.

access

special

charac-

Clear

Clear or backspace

ters (23

Press and

hold

availa-

Numbers

ble),

hold down . A table

appears. Press the key that

corresponds to the character.

Space

Special character ta-

ble appears if you

press and hold it.

Press Clear

briefly to cor-

rect back one letter. Hold

down to clear all text.

Another matching

word

Smart punctuation

Swap between T9 and

Multitap method

Press or to move the cur-

sor in the text to insert char-

acters or make corrections.

The following table displays the

available English characters. Other

languages display different charac-

ter sets.

Example

To enter Card in the display:

• Press and select Messages.

and return to the stand-by dis-

play.

Key

Character

Lowercase Upper case

1 . , - ' @ : ?

Network services

a b c 2

A B C 2

D E F 3

G H I 4

J K L 5

M N O 6

P Q R S 7

T U V 8

W X Y Z 9

Your network operator provides value

added services and contact phone num-

bers. Depending on your operator’s im-

plementation Applications, Services,

and/or Information appears in the dis-

play. Press and select Network Serv-

ices to access these menus.

d e f 3

g h i 4

j k l 5

m n o 6

p q r s 7

t u v 8

w x y z 9

Phone book

The phone book stores data, usually

names and telephone numbers, in the

phone or SIM memory.

• The phone can store up to 100

‘phone book cards’ which can con-

tain: family name, first name, icon,

home phone number, work phone

number, cellular phone number and

a note.

• SIMs can store up to 255 ‘SIM phone

book cards’. Actual numbers and

capacity depends on your SIM. SIM

phone book cards only contain the

name and number.

Both the SIM and the phone memories

are searched when you use the phone

book.

Short press swaps next letter

between upper or lower case.

Long press swaps all next let-

ters between upper or lower

case.

Short press

enters space.

Long press gives access to

special characters.

( ) % ! ; " _ @ § + # *

/ & = < > ¥ $ £ ¡ ¿ €

Short press moves the cursor

through the text one place.

Swap between Multitap and

T9.

Example

To enter Card in the display:

• Press and select Messages.

• Select Write new.

• Press and hold

appears. Press

times, C appears.

• Wait for the available characters

to go from the display, press and

Storing names and telephone num-

bers

until

briefly three

You can enter the names and num-

bers in the phone book manually or

copy them from SMS messages,

scratchpad or last dialled number

lists, etc. You can store the charac-

ters *, +, P (pause), # and _ togeth-

er with numbers. See page 20 to

learn how to enter text.

Store numbers in international

format using the '+' prefix (or

00) before the country code

followed by the telephone

hold

until

appears. Press

briefly once, a appears.

• Press

appears.

• Press

briefly three times, r

briefly once, d appears.

The word Card appears.

• Press to exit from this example

number. This ensures that the

number can also be dialled

from abroad.

There are several ways to store

numbers into the phone or SIM

memory:

Enter the requested data.

Press OK

Confirmation and number of

free locations appear.

Press and hold Exit

to return to the stand-by dis-

play.

• Using the menu:

Phone memory

Press . Select Phone Book.

Select Store. Select Phone

names.

Follow the steps in the previ-

ous procedure (“Directly from

the stand-by display”) start-

• Directly from the stand-by dis-

play:

Enter the number. Press

Store

Select Phone names.

A list appears.

Select the item corresponding

to the number you entered:

home, work or cellular.

ing with step

• From last dialled, received and

unanswered lists:

The following fields appear:

Display a number from one of

the above, then press

Field

Purpose

Options

Family or last

name

First name

Family name

First name

Select Store. Select Phone

names.

Follow the steps in the

“Directly from the stand-by

display” procedure starting

Enter the requested data.

Confirm each entry by press-

ing OK

with step

Select

an icon.

The

During number and name entry a short press on

Clear clears the last character. A long press clears

the whole display.

icons

SIM phone book memory

corre-

spond

You can enter the SIM memory

from the stand-by display, menu

or other locations.

keys on the keypad. Press

the key corresponding to the

required icon.

• Directly from the stand-by display:

Enter the number. Press

In this example pressing

Store

Select SIM names. Press

Modify or confirm the number

and press OK

selects

The following fields appear:

Field

Purpose

Phone number

(Home)

Home phone

number

Enter the name. Press OK

Confirmation and number of

free locations appear.

Phone number

(Work)

Work phone

number

Press and hold Exit

return to the stand-by display.

Phone number Cellular phone

(Cellular)

Note

number

Note or com-

ments for this

card

• Using the menu:

the phone or SIM. There are two

ways to view and call numbers in

the phone book:

• Directly from the stand-by display:

Press to display the phone book

list.

Press . Select Phone Book.

Select Store. Select SIM

names.

Enter the number and press

OK . Enter the name and

press OK . Confirmation

and number of remaining

locations appears.

Press and hold Exit

to return to the stand-by dis-

play.

• Using the menu:

Press and select Phone

Book.

Select Recall.

Either press OK

or enter up

• From other stored locations

to the first 3 initials of the

name required and then press

Numbers stored in the last dialled,

received, unanswered, scratchpad

and SMS message locations can all

be stored in the phone book:

Pressing

scrolls through

the phone book. To go directly to

another entry press the corre-

sponding alphabet key. For exam-

ple to go directly to entries

Display a number from one of

the above then press

Options

Follow the steps from the

previous procedure “Using

the menu” starting with step

starting with 'N' press

twice.

If you did not enter any initials,

the phone book displays the first

entry.

During number and name entry a short press on

Clear clears the last character. A long press clears

the whole display.

Press

to dial the number. If

there is a choice of numbers

for the phone book entry,

these appear. Select the one

that corresponds and press

A warning message appears when

selecting the phone book when the

SIM or phone memory is full.

Free space in the phone book

To see the remaining free space in

the SIM or phone:

Pressing Options

following menu choices:

displays the

Item

Edit

Function

Edits the name and

number entry

Press . Select Phone Book.

Select Remaining and use

or to display the remaining

memory spaces in the phone

or SIM.

Delete

Deletes the entry

Send SMS Sends SMS message

Press and hold Exit

Copies the entry to the

to return to the stand-by dis-

play.

SIM or the phone or

Copy

vice versa. You can

edit before copying

If available, the free memories in the FDN list also

appears.

Moves the entry to an-

other position. You

Move

Viewing and calling numbers in the

phone book

You can edit, delete, copy, move or

can edit before mov-

ing

Calls the number dis-

Call

access phone book entries stored in

played

Press and hold Exit

Press OK

to confirm the

to return to the stand-by dis-

play.

setting.

To view the numbers in the list:

Own number

Press . Select Phone Book.

Select Fixed Dialling.

Select View and use or

to scroll through the entries.

You can store your main 'Line 1'

voice mobile number, your voice

mobile number for Line 2 (Alternate

Line Service) and your data and fax

numbers into the SIM card. You can

enter them manually and name

them (e.g: Line 1 'Office'.

Press Options

to edit,

delete and copy numbers to

the phone or SIM.

To enter, edit or delete numbers in

the FDN list:

To view, name and edit your own

display number(s):

Press . Select Phone Book.

Select Fixed Dialling.

Press . Select Phone Book.

Select Add new. Enter the

PIN2 number if asked. Add,

edit, delete or copy new

numbers to the phone or

SIM.

You can use wild card spaces with numbers stored

in the FDN list. For example the number

+44 1707 278_ _ 9 allows you to call all num-

bers between 278009 to 278999.

Select Own numbers. The

mobile number for Line 1

appears.

Use or

to view line 2,

data and fax numbers.

To add or edit a name or

number press Edit

Press and hold Exit

to return to the stand-by dis-

play.

Phone book tones

30 pre-set ring tones are available,

10 with polyphonic (tri-tones) and

20 with mono-tones. Storage of up

to 40 ring tones is possible. That is,

you can add one self-composed

ring tone and 9 other ring tones

you download in addition to the ex-

isting 30 ring tones. If you want,

you can replace any of these ring

tones except the Trium ring tone.

To have different tones for incom-

ing calls where the identities are

known in the SIM or phone memo-

ry:

Fixed dialling numbers (FDN)

Fixed dialling only allows you to call

a group of numbers. All other num-

bers are rejected. FDN also prevents

call diverting and sending SMS mes-

sages to numbers not in the FDN

list. You can use wildcards to define

the groups. As this is a SIM depend-

ent feature, some SIM cards might

not support it. SIM capacity deter-

mines the maximum number of

FDN numbers you can store. To ac-

tivate/deactivate FDN you must

have the PIN2 code.

Press . Select Phone Book.

Select Phone Book Tones.

Select Phone names or SIM

To turn on or off FDN operation:

Press . Select Phone Book.

Select Fixed Dialling. Select

Status.

names. Press Select

Select the tone you want and

press Select . The phone

stores your selection.

Select On or Off. Enter the

PIN2 number.

Messages (SMS)

Item

Read text

Delete

Function

Displays the remain-

der of the text

Deletes the message

Replies to the sender

of the message

You can exchange short text messages

of up to 160 characters with other mo-

bile phones with SMS. You can also

store, edit and forward messages and

save any of the numbers they contain.

Replies to the sender

of the message with

the initial text

Forwards the mes-

sage to another user

Forwards a set of sev-

eral (5 maximum)

messages to 5 differ-

ent addressees

Stores or calls the

number(s) contained

in the SMS header or

text

Reading a received SMS message

When the phone receives an SMS

message a new SMS alert tone

(+ text)

Forward

sounds and

stores the message. If

appears. The SIM

flashes

there is no more space in the SIM to

store new messages. Delete previ-

ous messages to make space for

new ones.

Forward

to n

Press Read

to read all received

Numbers

messages (Inbox).

Reading stored SMS messages

The items of this menu depend on the type of mes-

sage received.

Press . Select Messages

(then SMS on Trium 110 m).

Turning on or off the message alert

tone

Each time a message is received the

SMS alert tone sounds. To turn on

or off this tone:

Select Inbox to display the

first message header.

Use

and

to select the

message.

Press or select Options

Read text to read the mes-

sage text.

Press . Select Messages.

Select Alert. Select On or Off.

You can now read all stored mes-

sages. For a given message,

shows the message is new.

shows you have already read the

message.

Press and hold Exit

to return to the stand-by dis-

play.

Preparing the phone to send SMS

messages

You can write and send text mes-

sages. To use SMS, check that the

number for the message centre is

configured:

Managing received and stored SMS

messages

After reading the SMS message

press Options

for the following

Press . Select Messages.

Select Settings.

menu:

Select Message centre.

If a number appears do nothing.

If empty, enter the number man-

ually (in international format) or

from a stored memory. If you do

not have this number, ask your

service provider for it.

Enter the draft text and press

Press and hold Exit

to return to the stand-by dis-

play.

to return to the stand-by dis-

play.

If required you can also choose the

validity period, format, paid reply

request and request a delivery re-

port. Default settings are assumed

if not set.

Editing a draft text

Press . Select Messages.

Select Draft texts.

Select the draft text to modify

and press Edit

Edit the text and press OK

Option

Description Default

Press and hold Exit

to return to the stand-by dis-

play.

Time held at

message

centre.

12 hours,

Validity

Period

Maxi-

Sending a new SMS message to

one addressee

1 day, 2

mum

days or

Maximum

(defined by

operator)

Press . Select Messages.

Select Write new.

You can either choose a draft

text (if you set one up) or

enter the message text and

Selects for-

mat of mes-

Format sage, text,

voice, fax or

pager

Text

press OK

Select Send.

Choose a message template

(if you have stored 2 or more

templates) and then enter the

destination number or select

Paid

Reply re-

Off

Reply to

quested

Status

report to

Delivery re-

port

Names

to choose a

number from a phone book

entry. Press to validate your

choice. Press OK . Sending

and sent confirmation

Creating a draft text

Parts of a message are often the

same, such as the greeting or signa-

ture. To save time, you can create a

draft text for these parts. Then

when you want to write a message,

you access the draft text and only

write the specific part of the mes-

sage. You can set up to 10 message

drafts, which can hold up to 48

characters each. The mobile memo-

ry stores the drafts.

appears for each addressee.

Press and hold Exit

to return to the stand-by dis-

play.

Sending a new SMS message to

many addressees

Press . Select Messages.

Select Write new.

You can either choose a draft

text (if you set one up) or

enter the message text and

To create a draft text:

Press . Select Messages.

Select Draft texts.

Choose any blank template

([...]) and press Edit

press OK

Select Multicast.

time appears. If you request the sta-

tus of a sent message the network

sends a status report (if this feature

Choose a message template

(if you have stored 2 or more

templates).

Enter up to 5 destination

numbers or select Names

to choose up to 5 numbers in

the phone book.

is supported). Press OK

to ac-

knowledge the report.

To act upon a received status report

and its related message:

Press to validate your

choice. Press OK

Press Options . The follow-

ing menu appears:

Sent confirmation appears.

Press and hold Exit

Item

Action

to return to the stand-by dis-

play.

Deletes the corre-

sponding sent SMS

message and the sta-

tus report

To acknowledge the

status report and

clear the display

Delete

Storing a new SMS message

message

Clear

Press . Select Messages.

Select Write new.

You can either choose a draft

text or enter the message text

and press OK

Displays the corre-

sponding sent SMS

message

Associ-

ated

message

Select Store.

Press and hold Exit

to return to the stand-by dis-

play.

Sends the same mes-

sage again

Send

again

Modifying and re-sending messag-

es in the outbox

Select the action required and

press OK

The outbox contains unsent draft

messages, stored sent messages

and sent but undelivered messages.

You can modify and re-send these

as new messages.

Re-usable message templates

The Msg templates menu option

appears in the Messages - Settings

menu if your SIM supports this fea-

ture. Message templates are sets of

message parameters and are stored

in SIM memory. You can name and

select the templates when needed.

To create a message template:

To select an outbox message:

Press . Select Messages.

Select Outbox and use or

to scroll to the desired

message. Messages are either

“transmitted” (

sent” ( ).

) or “to be

Press . Select Messages.

Select Settings.

Press Options

to read,

Select Msg templates.

Choose any blank template

([...]).

delete, request a status

report, send (or re-send) to

one addressee, edit a sent

message and send (or re-

send) to many addressees.

Enter the template Name,

Message centre number,

Validity period and Format.

Follow the instructions dis-

played on the screen.

Default settings for pay reply and

status are assumed 'off' unless set

and are common to all templates. If

you set one template only the

Status request on sent messages

If you request the status of a deliv-

ered message the delivery date and

phone uses it by default. Otherwise

select the template you want when

sending a message.

Reading a received EMS message

When the phone receives an EMS

message a new alert tone sounds

and

appears. The phone stores

Storage consumption

To consult the memory used by

SMS:

the message. If flashes there is no

more space in the phone to store

new messages. Delete previous

messages to make space for new

ones.

Press . Select Messages.

Select Storage.

Use or

to view all the

Press Read

messages (Inbox).

to read all received

SMS storage information

(SMS storage, SMS outbox

and SMS inbox).

Reading stored EMS messages

Press and hold Exit

Press . Select Messages.

Select EMS.

Select Inbox.

to return to the stand-by dis-

play.

EMS

Use

and

to select the

message.

EMS stands for Enhanced Message Se-

vice. This feature allows to receive mes-

sages with text, melodies, images and

animated icons. These messages are

sent via the Internet; they may bear pro-

motional information or commercial of-

fers.

The use of this feature is registration de-

pendent and may not be available in all

areas.

Press or select OK to read

the message text or delete

the message.

You can now read all stored mes-

sages. For given message,

shows the message is new.

shows you have already read the

message.

Calls & Times

Access the Calls & Times menu to check

the details of individual incoming and

outgoing calls, the duration of the last

call or the total time for all previous

calls.

EMS Menu

Press . Select Messages

Select EMS.

Select the menu item you

want to access.

Press Cancel

Calls log

return to the stand-by display.

Calls log stores the identity, time,

date and call duration of the last

10 numbers dialled, the last 10 re-

ceived unanswered calls and the

last 10 received calls. The call logs

are common for both Line 1 and

Line 2.

Inbox

To read or delete stored messages

My services

To reach the list of registered services

Settings

To reset or delete the EMS contents

Service Registration

To enter the address of the service sites.

Press . Select Calls & Times.

Select Calls Log.

Select Last dial, Unan-

swered or Received.

1. Available on Trium 110 m only

Use or

the list.

If the caller’s number is not availa-

ble, Unknown number appears

(unanswered and received lists).

to scroll through

Select Show.

Use or

to view all the

timer information.

The call type and the accumulat-

ed times of outgoing and incom-

ing calls appears.

Pressing

while on a displayed

number calls that number.

Pressing Options

accesses the

following menu:

Item

Action

Stores the number in

the phone book

Store

Press Details

to display

Delete

all

Deletes the entry

Deletes all the entries

details on My network,

National roaming and

Int’nal roaming calls.

Edits the displayed

number

Views the details -

name, number, time

Edit

Press or Exit

to return to

the previous display.

Press and hold Exit

to return to the stand-by dis-

play.

Details and date and call dura-

tion of the highlighted

number

If Line 2 is subscribed to 'All Calls' for Line 1 and

Line 2 appear separately.

Makes a call to the

Call

Balance information (subscription

service only)

Some networks provide your call

time balance. You have to call a

specific number (given by your net-

work operator) in order to get this

information.

number

Send

SMS

Sends SMS message

Use

to select the required

option and follow the display

prompts.

Press and hold Exit

to re-

Contact your service provider for

availability and details.

turn to the stand-by display.

Press when in stand-by display to access the

last 10 dialled calls.

Press . Select Calls & Times.

Select Call timers.

Select Balance information.

Call times

Call times stores the duration of the

last call, total accumulated time of

all calls and total time for Line 1 and

Select Set number (only nec-

essary the first time you use

this service) to check that the

balance information centre

number is set. If not, enter

the number provided by your

service provider and press

Line 2. The Details

sub-menu

stores times for calls made and re-

ceived through the subscription

network and through other (nation-

al and international) networks.

Select Call. The phone calls the

centre. Press

when you

Press . Select Calls & Times.

Select Call timers.

want to end the call.

Select Call costs.

Select Display cost type.

Select Currency. The present

currency settings appears.

Press Edit . Enter the PIN 2

code and press OK

Enter the abbreviated letters

of the currency. Press OK

Press and hold Exit

to return to the stand-by dis-

play.

Reminder - Call duration

You can set a call duration reminder

in multiples of 1 minute (1 - 59

min.) intervals. It beeps at the set

intervals.

Enter the cost per unit in the

Press . Select Calls & Times.

Select Call timers.

Select Reminder.

Select On (or Off).

Select the period (between 1

and 59 mins).

selected currency. Press

Press and hold Exit

to return to the stand-by dis-

play.

To set call cost type to units:

Press OK

Press . Select Calls & Times.

Select Call costs.

Select Display cost type.

Select Units.

Press and hold Exit

to return to the stand-by dis-

play.

Press and hold Exit

Call timer - reset

To reset all the call timers, you need

the 4 digit phone lock code.

return to the stand-by display.

When you set the cost type to units the credit limit

and the remaining credit appear in units.

Press . Select Calls & Times.

Select Call timers.

Select Reset.

Setting the credit limit - in units or

currency

You can set a credit limit in units or

currency. The phone prevents mak-

ing and receiving all chargeable

calls when the phones reaches the

credit limit. You can still make

emergency calls.

Select Yes or No.

Enter the phone lock code

and press OK

Press and hold Exit

to return to the stand-by dis-

play.

Call costs management (subscrip-

tion service only)

Press . Select Calls & Times.

Select Call costs.

Select Credit Limit. The

present credit limit setting

appears.

An Advice of Charge (AoC) subscrip-

tion service shows the cost of the

last call made, the accumulated to-

tal cost of all calls and the remain-

ing balance in units or currency of

any 'cost limit' you set. Check with

your service provider to see if they

offer this feature.Select the curren-

cy and cost per unit; otherwise call

costs display in generic units.

Press Edit . Enter the PIN 2

code and press OK

Enter the credit limit (use

to enter a decimal point).

Press OK

to validate.

Press and hold Exit

to return to the stand-by dis-

play.

When you enter a credit limit the selection from the

'Credit Limit' displays Edit or Set No Limit.

To set currency and cost per unit:

Press . Select Calls & Times.

Show costs

Press and hold Exit

to return to the stand-by dis-

play.

Press . Select Calls & Times.

Select Call costs.

You can assign names to Line 1 and Line 2, e.g.

Office and Home. See page 25 for details. You

must select the line to make outgoing calls. You

can receive calls from either line.

Select Show.

Use or

to display the

cost of the Last Call, All Calls

and the Remaining credits.

Settings - customising

your phone

Press and hold Exit

to return to the stand-by dis-

play.

Phone settings

The Cost Type menu units or currency setting deter-

mines whether the remaining credit displays units

or currency.

Keypad lock

See page 15 for more informa-

tion.

Call costs - resetting all costs to

zero

To reset all the call costs to zero you

Language selection

To select the language of your

choice:

need the PIN 2 code.

Press . Select Calls & Times.

Select Call costs.

Select Reset.

Select Yes to reset the costs

or No to exit.

If you select Yes, enter the

PIN 2 number and press

OK . All Costs Reset

appears briefly.

Press . Select Settings.

Select Phone settings. Select

Language.

Use or

to select a lan-

guage from the displayed list.

Press Select to validate.

Press and hold Exit

to return to the stand-by dis-

play.

Press and hold Exit

To reset the phone to the language of the SIM

enter *#0000#.

To reset the phone language to English enter

*#0044#.

to return to the stand-by dis-

play.

Alternate line service - selecting

Line 2 (subscription service)

Some GSM 1800 operators support

the use of a second line for users.

You can have two mobile phone

numbers, e.g. a business and per-

sonal line. To select the line for out-

going calls:

Tones - Alert mode

To turn on or off the audible in-

coming ring tone, alert and alarm

tones:

• Using the menu:

Press . Select Settings.

Select Phone settings. Select

Tones.

Select Alert tones.

Select Ring, Vibrate, Vibrate

& ring or Vibrate then ring.

Press . Select Calls & Times.

Select Line selection.

The current line selection

appears.

Press and hold Exit

Use or

to scroll to the

line required and press

Select or to validate

your choice.

to return to the stand-by dis-

play.

• Directly from the stand-by dis-

play:

Select Phone settings. Select

Tones.

Press

displays Ring, Silent,

Select Volume.

Select Ring, Keys, Conversa-

tion or Alarm.

Vibrate, Vibrate & ring or

Vibrate then ring.

Scroll to the desired setting.

The display confirms the selec-

tion, naming the volume to be

adjusted.

Press Select to validate your

choice. (If any of the vibrate

options are selected the

phone briefly vibrates).

appears.

1. If you select Ring but the ring tone volume is off

the icon appears.

2. appears if you select Vibrate, Vibrate & ring or

Vibrate then ring. It takes precedence over

3. When the phone is connected to either the Desk

Top Charger, HF kit, CLA or AC adaptor the phone

rings instead of vibrates.

4. If you choose the 'Vibrate' or 'Vibrate then ring'

option, the vibrating action replaces all the alert

and alarm tones.

Use or

ting.

Press OK

setting.

Press and hold Exit

to return to the stand-by dis-

play.

to adjust the set-

to validate the

Ring tone selection

To choose an incoming ring tone:

Press . Select Settings.

Select Phone settings. Select

Tones.

During a call, you can adjust the

conversation volume by using

Select Melodies.

If the ring tone volume level is set to 0 displays.

To help you identify incoming

calls you can give the Stand-

ard/Line 1, Phone names,

SIM names and Line 2 calls

and Alarm different ring

tones.

Automatic ramping

Your phone was designed with an

automatic

ramping

feature.

When your phone rings, the vol-

ume level is lower than the vol-

ume level you have set.

Adjustment is made from low or

medium volume level to the vol-

ume level you have set (see “Vol-

ume adjustments”, page 33).

This feature is a default setting

and cannot be deactivated. Ram-

ping and Automatic Ramping are

compatible; both will work if

Ramping is activated.

Use or

to highlight the

required call type and press

to select it.

Use or

to listen to the

different ring tones. Press

to select the current tone.

Press and hold Exit

to return to the stand-by dis-

play.

Volume adjustments

To individually adjust the volume

level of the ring tone, key tones,

alarm tones and incoming audio

Ramping

from the stand-by display, press

Alternatively, access Volume con-

trol from the Settings menu:

Ramping causes the incoming

ring tone to increase step by step

to the maximum volume level.

Press . Select Settings.

Menu graphics

Press . Select Settings.

Select Phone settings. Select

Tones.

Select Volume.

Select Ramping.

Select On or Off.

Choose from a set of graphics to

personalise your main menu im-

ages and icons. There are 3 menu

themes.

To change the menu graphics:

Press and hold Exit

Press . Select Settings.

Select Phone settings. Select

Menu graphics.

to return to the stand-by dis-

play.

When turned on the volume of the incoming ring

tone starts from the selected ringer volume (just

after the automatic ramping) and rises to the max-

imum volume.

Use

to scroll the sets of

menu graphics and press

Select

choice.

to validate your

Press and hold Exit

Backlight - setting

return to the stand-by display.

To set the backlight during key

entry or incoming ring tone, you

have two options:

• On for 10 sec.: the display and

key backlight stays on for

10 seconds after the last key

press or incoming call.

• Off: the backlight stays off

except on incoming call.

Any key answer

To enable any key (except

No ring

swer an incoming call:

and

) to be pressed to an-

Press . Select Settings.

Select Phone settings. Select

Keys.

Select Any key answer.

Select On or Off.

Press and hold Exit

to return to the stand-by dis-

play.

Press Select. Select Settings.

Select Phone settings. Select

Display.

Select Backlight.

Select one of the two set-

tings. Press to validate.

Softkeys - programming the

softkeys

You can change the function of

the softkeys. There are two ways:

• Directly from the stand-by dis-

play:

Press and hold Exit

to return to the stand-by dis-

play.

Display contrast

To modify the display contrast be-

cause of bad light conditions:

Press and hold down the left

or right

Press . Select Settings.

Select Phone settings. Select

Display.

Use or

the choice of softkey options.

Press Select

your choice.

The screen confirms your

selection and returns to the

stand-by display showing

your new softkey function.

to scroll through

to validate

Select Contrast.

Adjust the contrast using

Press OK

setting.

to validate the

Press and hold Exit

• Using the menu:

Press . Select Settings.

to return to the stand-by dis-

play.

automatically answers an incom-

ing call after approximately 5 sec-

onds.

Select Phone settings. Select

Keys.

Select Softkeys functions.

Select Left softkey or Right

softkey.

Press . Select Settings.

Select Phone settings. Select

Auto features.

Press Select

on the softkey

option of your choice.

Select Auto-answer.

Select On or Off.

Press and hold Exit

to return to the stand-by dis-

play.

Press and hold Exit

to return to the stand-by dis-

play.

(......) in the display means that a previously SIM

dependent or subscription service assigned to that

softkey is no longer available. For example Line 2

selection.

Auto-retry

To automatically retry the

number of a failed call (up to

10 times):

Speed dialling

You can assign phone book num-

bers to keys . Hold down

the key to dial the number. The

phone reserves exclusively for

Press . Select Settings.

Select Phone settings. Select

Auto features.

Select Auto-retry.

Select On or Off.

Press and hold Exit

to return to the stand-by dis-

play.

the voice mail number. The phone

automatically assigns this key to

the voice mail number if stored

(see “Voice mail”, page 38).

You can select any stored

number.

When activated, Auto-retry and a

countdown timer to the next call

attempt appears. An auto-retry

warning tone sounds each time

the phone attempts a new retry.

If successful, proceed with the

To assign phone book numbers to

the speed dialling keys:

Press . Select Settings.

Select Phone settings. Select

Keys.

call as normal. Press Exit

Select Speed Dial.

any key during the retrying proc-

ess to cancel auto-retry and end

the dialling process for that call.

Use or

next key.

to scroll to the

Select Names

to choose

the phone book entry and

Security features

press Select

your choice.

to validate

The security features described in

this section protects your phone

from unauthorised use.

Press and hold Exit

to return to the stand-by dis-

play.

For all codes

When requested, enter the code,

which appears as asterisks (*) and

If you delete the number from the phone book this

also deletes it from the associated key.

press OK

If you make

Clear and enter the correct

digit(s) before pressing OK

Auto answer

mistake press

This feature only works when you

connect the phone to a hands

free car kit or headset. The phone

Avoid using codes similar to emergency numbers

such as 999 or 112 to prevent accidental dialling

of these numbers.

PIN code

The 4-8 digit PIN code for the SIM

protects it from unauthorised

use. When enabled the phone re-

quests the PIN code each time the

phone is turned on. If you enter

the wrong PIN code three times in

succession your SIM card is

blocked and you need the 8 digit

PUK code from your service pro-

vider (see page 37). To turn on

and off the PIN:

KEEP A RECORD OF YOUR CODES

AND KEEP THEM IN

SAFE

PLACE. FAILURE TO DO SO CAN

CAUSE YOU CONSIDERABLE IN-

CONVENIENCE.

Phone lock code

A phone lock code prevents unau-

thorised access to the phone and

WAP™ settings. You also need it

to reset the call timers. The facto-

ry setting is 0000. Reset this code

and keep it in a safe place, sepa-

rate from the phone. When ena-

bled the phone asks for the code

each time the phone is turned on.

To change the phone lock code:

Press . Select Settings.

Select Phone settings. Select

Security.

If already off, PIN enable

appears.

If already on, PIN disable

and PIN change appear.

Press Select

and follow

Press . Select Settings.

Select Phone settings. Select

Security.

Select Phone lock.

Select Change code and fol-

low the display prompts.

the displayed prompts.

Press OK

to validate your

entry. PIN enabled or PIN

disabled appear briefly to

confirm your action.

Press and hold Exit

to return to the stand-by dis-

play.

Press OK

new code.

to validate the

To change the PIN code (PIN must

first be enabled):

Press and hold Exit

to return to the stand-by dis-

play.

Press . Select Settings.

Select Phone settings. Select

Security.

To turn on or off the phone lock

code:

Select PIN change and follow

Press . Select Settings.

Select Phone settings. Select

Security.

Select Phone lock.

Select On or Off.

The phone requests the

phone lock code to authorise

your selection.

the displayed prompts.

Press OK

new PIN.

Press and hold Exit

to return to the stand-by dis-

play.

to validate your

PIN2 code

The PIN2 code prevents unau-

thorised access to FDN opera-

tions, modifying the FDN phone

book, setting calls costs to zero,

modifying the costs display fea-

tures. You can change it but you

Press and hold Exit

to return to the stand-by dis-

play.

Phone lock still enables you to make emergency

calls.

can not turn it on or off.

To change the PIN2 code:

Select Set time or Set date.

Enter the time (in 24 hour

format) or date in the format

shown. (If required use

Press . Select Settings.

Select Phone settings. Select

Security.

and

)

Press OK

to validate your

Select PIN2 change and fol-

entry.

low the display prompts.

Press and hold Exit

to return to the stand-by dis-

play.

Press OK

to validate your

new PIN2 code.

Press and hold Exit

to return to the stand-by dis-

play.

1. An error message appears if you make a wrong

entry.

2. The time/date are displayed when the phone is

on. It does not show the year.

PUK code

Only your service provider can

give you the 8 digit PUK (PIN un-

block key). Use it to 'unblock' a

PIN whose code has been entered

incorrectly three times. A PUK

code cannot be changed.

Enter the PUK code and press

OK . Enter a new PIN code by

following the displayed prompts.

3. You may have to re-enter the time and date if

the battery was taken out.

Default (factory) settings

Use the Settings menu to return

to the factory settings. This does

not affect the phone book en-

tries, phone lock code or SIM.

Press . Select Settings.

Select Phone settings. Select

Default settings.

If you enter the wrong PUK code 10 times in suc-

cession your SIM card cannot be used again. Con-

tact your service provider for a new card.

Select Yes or No.

Press and hold Exit

to return to the stand-by dis-

play.

PUK2 code

Only your service provider can

give you the 8 digit PUK2. Use it

to unblock a PIN2 whose code has

been entered incorrectly three

times. You cannot change the

PUK2 code.

Enter the PUK2 code. Enter a new

PIN2 code by following the dis-

played prompts.

The following are the factory de-

fault settings:

Feature

Alert Tones

Ring Tones

Factory setting

Ring

Trium

Volumes,

Ring, Key,

Speech and

Alarm.

Mid values

If you enter the wrong PUK2 code 10 times in suc-

cession you are unable to use the features requir-

ing the PIN2 code. Contact your service provider for

a new card.

Backlightand On for 10 sec. and

Contrast

mid value

Any Key,

Auto-Retry

and Auto An-

swer fea-

tures.

Time & date setting

To set the current time and/or

date:

Off

Press . Select Settings.

Select Phone settings. Select

Time & date.

Ramping

Menu graph-

ics

Off

Trium

Melody download

Press and hold Exit

to return to the stand-by dis-

play.

You can also download melodies

from the Trium web site

(www.mitsubishi-telecom.com).

This site downloads the melodies

to your phone using SMS. When

the download completes,

Calling the voice mail centre to

check for messages

There are two ways:

• To dial the voice mail centre

directly after the receipt of a

message:

Press and hold down

Press Options

and then select

Play to play the melody.

Press Options

and then select

Install to store the melody.

• Or from the menu:

Voice mail

Press . Select Settings.

Select Voice Mail.

Select Call.

Voice mail operates like an answer-

ing machine. Contact your service

provider for details.

Dialling proceeds as for a normal

call.

If a voice mail number is not stored when you

select Call, the phone asks you to enter the voice

mail number. Proceed as described in Storing a

voice mail centre number, page 38.

Storing a voice mail centre number

If your SIM does not automatical-

ly include the voice mail centre

number, you must manually set

it:

Press . Select Settings.

Select Voice Mail.

Select Number. When

prompted enter the number

manually or from a stored

memory.

GSM services

The services described hereafter

are a non-exhaustive list of GSM

services. Please contact your op-

erator/service provider for more

information.

Press OK

entry.

to validate your

Press and hold Exit

to return to the stand-by dis-

play.

If you subscribe to the 'Line 2' service, store the

voice mail centre number separately for that line.

The phone automatically assigns the voice mail

number to speed dial location number 1 (see

Speed dialling on page 35).

Turning on/off the voice mail alert

tone

To turn on/off the voice mail alert

tone:

Press . Select Settings.

Select Voice Mail.

Select Alert. Select On or Off.

Diverting incoming calls (network

service)

Call diverting diverts incoming

calls, whether voice, fax or data,

to another number.

Press Select

or to vali-

date your selection.

The display confirms your

request.

Press and hold Exit

to return to the stand-by dis-

play.

1. If you select 'On no reply' option you must also

enter a delay period of 5, 15 or 30 seconds.

2. Call diverts for both Line 1 and Line 2 must be

set individually. Select the out-going line before

following the above procedure. To carry out a call

divert on the other line you must select this other

line first (menu Calls & Times - Line selection).

To turn on call divert:

Press . Select Settings.

Select GSM Services.

Select Call diverting to access

the following menu:

Divert op-

tions

Action

Diverts all incom-

ing voice calls un-

conditionally

To turn off or check the status of

call divert:

Always

Press . Select Settings.

Diverts all voice

calls when the

phone cannot be

reached, i.e. out

of service

Select GSM Services. Select

When not

reachable

Call diverting.

Select from the divert options

and press

Select Cancel or Status.

The phone confirms your

selection.

Press and hold Exit

to return to the stand-by dis-

play.

Diverts all voice

calls when the

phone does not

answer

Diverts all voice

calls when the

phone is busy

On no reply

When busy

To cancel all (multiple) diverts:

Diverts all voice

calls when Not

Press . Select Settings.

Select GSM Services. Select

Call diverting.

Select Cancel all. The phone

confirms your selection.

Press and hold Exit

to return to the stand-by dis-

play.

This action cancels all voice diverts (for voice, faxes

and data calls) for the line currently in use. To can-

cel call diverts for the other line you must select this

other line first (menu Calls & Times - Line selec-

tion).

All conditions Reachable, No Re-

ply and When

Busy

Cancel all

Cancels all diverts

Diverts uncondi-

All FAX calls tionally all incom-

ing fax calls

Diverts uncondi-

All DATA calls tionally all incom-

ing data calls

Use or

to select the

divert condition and validate

Caller Line Identity - showing/hiding

your mobile number

Most networks allow the Caller

Line Identity feature (CLI) i.e.

showing the incoming number

(ID) while receiving a call. Select-

by pressing Select

Select Activate.

Use or

to choose

between Voice Mail, Names

or Number.

ing Receiving caller ID allows

you to check its availability from

the network.

Receiving caller ID

To find out whether a network

presents the ID of incoming calls:

Select Hide my ID or Show

my ID.

Press and hold Exit

to return to the stand-by dis-

play.

Finding out your current ID set-

ting

Press . Select Settings.

Select GSM Services. Select

Sending my ID.

Select GSM Services. Select

Receiving caller ID.

The network returns either

Presentation available or

Presentation unavailable.

Select Status.

The phone displays your cur-

rent setting, taking into

account both network and

phone settings.

Press and hold Exit

to return to the stand-by dis-

play.

Press and hold Exit

To hide your number, on a call by

call basis, add #31# before the

number you are calling. Alterna-

tively you can ask your service op-

erator to always disable the

sending of your mobile number.

In this case to reveal your

number, on a call by call basis,

add *31# before the number you

wish to call.

to return to the stand-by dis-

play.

Network

When turned on, the phone auto-

matically searches for the last net-

work it was registered on. If this is

not available, the phone auto-

matically searches and, if able

and allowed, selects a network.

Editing the preferred list

You can change the order and

names in the preferred networks

list stored in your SIM by choos-

ing from the list in your phone.

This is useful while roaming if you

know a network provider that is

more economical than another.

Standard network setting

To reset the standard network

setting for sending your mobile

ID:

Press . Select Settings.

Select GSM Services. Select

Sending my ID.

Select My settings.

Press . Select Settings.

Select GSM Services. Select

Network.

Select Preferred list. A list of

networks appears.

Select Preset. The phone

resets to the network setting

agreed with your service pro-

vider.

Press and hold Exit

Use or

to view the list.

Press Options to change it.

The following items appear:

to return to the stand-by dis-

play.

Hiding or showing your number

Press . Select Settings.

Select GSM Services. Select

Sending my ID.

Select My settings.

Press Select to confirm the

selection.

Requesting... followed by

the name of the network

appears. The phone then

returns to the stand-by dis-

play.

Option

Description

Displays the gener-

al list of all known

networks con-

tained in the

Modify by list

phone in alphabet-

ical order

You cannot delete a network from the forbidden

list. This list is automatically updated when you

perform the manual network selection.

Edits or enters a

network number

(MCC MNC) if you

know this informa-

tion.

Modify by

code

Selecting automatic search (normal

default setting)

To perform an automatic search

from the preferred list:

Delete

Deletes an entry

Press Select

selection.

to confirm the

Press . Select Settings.

Select GSM Services. Select

Network.

Select Search.

Select Automatic.

Press and hold Exit

to return to the stand-by dis-

play.

Your SIM may contain a forbid-

den list of networks which cannot

be used. To view the forbidden

list or show the home network:

Press and hold Exit

to return to the stand-by dis-

play.

Press . Select Settings.

Select GSM Services. Select

Network.

Select either Forbidden or

Home network.

A list of the forbidden net-

works or the home network

appears.

Press

to return to the

stand-by display.

Selecting manual search

To select a specific network, e.g.

one which provides better cover-

age in your current location:

Press . Select Settings.

Select GSM Services. Select

Network.

Select Search.

Select Manual. A confirma-

tion screen and Scanning for

networks... appears.

Use or

to select a net-

work from the list shown.

Call barring (network service)

To stop different types of calls be-

ing made and received on the

phone, you need a call barring

password available only from

your service provider.

tial password. To change the

password:

Press . Select Settings.

Select GSM Services. Select

Call barring.

Select Change password and

follow the displayed prompts.

Press . Select Settings.

Select GSM Services. Select

Call barring.

Press OK

to validate.

Press and hold Exit

to return to the stand-by dis-

play.

Select Outgoing calls or

Incoming calls. Choose:

Summary of code/password entry

chart

Select

Meaning

Bars all outgo-

ing calls

Bars only all

outgoing in-

ternational

calls

Bars all outgo-

ing interna-

tional calls

except for oth-

er subscribers

within the us-

ers home net-

work

Outgoing

- All outgoing

Number blocked

Pass-

word

Length

of trials

allowed

forgot-

ten

Outgoing

- Int'nal calls

Return

Phone

unlock 4 digits

code

phone to

manufac-

turer

Unlimited

3 tries

Outgoing

- Int'nal excl.

home

Un-

4-8

blocked

by use of

PUK code

digits

Un-

blocked

by use of

PUK2

Incoming

Bars all incom-

ing calls

4-8

PIN2

3 tries

- All incoming

digits

Bars all incom-

ing calls when

not on the

code

Incoming

- Roaming only

Contact

your serv-

ice pro-

vider

Contact

your serv-

ice pro-

vider

home network

PUK

8 digits

10 tries

Select the option using or

. Press Select

Select Activate. Enter the

password and press OK

The network confirms the

selection.

PUK2

Call

Contact

your serv-

ice pro-

vider

bar-

ring

Network

deter-

mined

Press and hold Exit

4 digits

to return to the stand-by dis-

play.

pass-

word

Call barring password

To cancel or check the status of a

call bar:

Use the call barring password to

select the call barring levels out-

lined in the GSM Services - Call

barring menu (see page 42). Your

service provider gives you the ini-

Press . Select Settings.

Select GSM Services. Select

Call barring.

Use or

to select the bar

to cancel or check the status

Select Broadcast.

and press

Select Message types. Press

You must have the password

to cancel a call bar.

Options

Select Modify by list (or Mod-

ify by code if type number is

known).

Press and hold Exit

to return to the stand-by dis-

play.

Scroll to the message type

To change the password:

required. Press Select

validate your selection. The

Press . Select Settings.

Select GSM Services. Select

Call barring.

Select Change password.

Enter the old password once

and the new password twice

when prompted. The phone

confirms the change.

display confirms your choice.

Press Options

again to

select more message types

from the list, enter a message

type number if known, or

delete a message type.

Press and hold Exit

to return to the stand-by dis-

play.

Press and hold Exit

to return to the stand-by dis-

play.

To turn on or off the broadcast

service

Broadcast - cell broadcast messag-

es (Network Service)

Press . Select Settings.

Select Broadcast.

Select On/Off.

Networks can broadcast messages

to all GSM users that can give infor-

mation about local area dialling

codes, weather reports, traffic news

etc. You can decide what type of in-

formation to receive by choosing

the corresponding number. You

can program to receive up to 5 dif-

ferent types of messages.

You can select from a list of 16

standard message types. New mes-

sage types can be programmed into

the selection list using the 3 digit

cell broadcast type number. Con-

tact your service provider for more

details.

Select On or Off.

Press and hold Exit

to return to the stand-by dis-

play.

Reading broadcast messages

Broadcast messages appear in the

stand-by display only. The phone

suppresses them during conver-

sation or menu operation. A mes-

sage can be up to 93 characters in

length and cover several pages.

Pages scroll automatically about

every five seconds. To scroll

down, press

Options during message display

Press on Exit to clear the mes-

Enter at least one message type into

the selection list or you cannot acti-

vate the service.

To enter a message type in the se-

lection list

sage currently displayed. Press

to dial the number displayed in

the message.

Pressing Options

following menu:

displays the

You can enter up to 5 different

message types.

Press . Select Settings.

Use or

to select a lan-

Option

Delete

Action

To delete the cur-

rent message

To delete all mes-

sages stored in

the queue

To display all

phone numbers

found in the mes-

sage text. This al-

lows dialling or

storing them in

the scratchpad if

required

guage from the displayed list.

Press to validate.

Press and hold Exit

to return to the stand-by dis-

play.

Delete All

Numbers

Using the office tools

The Office Tools menu contains

scratchpad, an alarm clock, an auto-

switch feature and a calculator.

Scratchpad

You can store up to 5 separate en-

tries of 36 characters in the scratch-

pad.

Broadcast

Off

To turns off cell

broadcast

Press . Select Office Tools.

Turning the broadcast alert tone on

or off

To turn on or off the alert tone

the phone gives when a broad-

cast message arrives:

Select Scratchpad.

Select Read Notes. Use or

to scroll through the

entries.

Select Write Notes to make a

new scratchpad entry.

Press . Select Settings.

Select Broadcast.

Select Alert.

Press Options

tries to access the following menu:

when reading en-

Select On or Off.

Item

Action

Save a number to

the phone book

Modify an entry

Delete an entry

Delete all entries

Call the number

displayed in the

entry

Press and hold Exit

to return to the stand-by dis-

play.

Store

Edit

Deleting or editing a message type

from the list

To delete or edit a message type:

Delete

Delete all

Press . Select Settings.

Select Broadcast.

Select Message types. Press

Options

Select Modify by list or Mod-

ify by code.

Press and hold Exit

to return to the stand-by dis-

play.

Call

Alarm clock

To set a daily 'Reminder Alarm':

When 'on' the alarm activates at the same time

every day until turned off.

Press . Select Office Tools.

Select Alarm clock.

Select On and enter the alarm

Broadcast language

To select the broadcast language:

time (in 24 hour format) or

press OK

to accept the dis-

Press . Select Settings.

Select Broadcast.

Select Language.

played time.

Confirmation appears.

on, you must re-enter your PIN

code. The phone does not go into

power saving mode until you enter

your code. To activate the auto-

switch:

Press Select or

to return to

the stand-by display.

appears.

The alarm sounds for up to

1 minute. Alarm clock and a vibrat-

ing bell symbol appear with the cur-

rent time and the softkeys,

Press . Select Office Tools.

Select Auto-switch.

Select Auto-switch-on.

Select On.

Enter the time you want the

phone to turn on and

press OK . Confirmation

appears.

Valid.

and No ring

. During a

call, the alarm also sounds.

To stop the alarm:

Press Valid.

To use as a Reminder or Snooze

Alarm:

Press No ring , or any other key

(except Valid. ) to stop the

alarm. The alarm icon remain on

the display and the alarm rings

again 3 minutes later.

Select Auto-switch-off.

Select On.

Enter the time you want the

phone to turn off and

press OK

Press and hold Exit

to return to the stand-by dis-

play. The icon appears in

the stand-by display.

You can repeat the snooze for up to

15 minutes, after which the phone

returns to its previous state, either

off or on stand-by.

To turn off the auto-switch:

To turn off the alarm:

Press . Select Office Tools.

Select Auto-switch.

Select Auto-switch-on.

Select Off. Stored appears.

Select Auto-switch-off.

Select Off. Stored appears.

Press . Select Office Tools.

Select Alarm clock.

Select Off. Confirmation

appears.

Press and hold Exit

to return to the stand-by dis-

play.

Press and hold Exit

to return to the stand-by dis-

play.

Caution - Please remember to

turn off the alarm feature when

boarding an aircraft where the

use of a mobile phone is not

permitted and is illegal. Alterna-

tively, you can remove the bat-

tery after turning off the phone.

See the General safety warnings

on page 4.

Calculator

To access and use the calculator:

Press . Select Office Tools.

Select Calculator.

Enter a number and press

several times to choose +, -,

* or / or

to enter a ,.

Enter the second number and

either repeat step

or select

Auto-switch

to compute. Select

Clear to correct any mis-

takes or clear the display.

Press to return to the

stand-by display.

You can set your phone to switch

on and off automatically. Turning it

off helps to conserve battery life.

Please note that during auto-switch

or press

display.

to return to the stand-by

Games

The availability and appearance of the

games depend on your network opera-

tor and on your mobile phone version

(Reshape and Push games are available

on Trium 110 and Trium 110 m only).

Receiving an incoming call while playing may not

allow you to resume the current game.

Trium 110 p games

The Trium 110 p Games menu al-

lows the downloading of new

games onto your mobile. Up to 2

games can be stored in the phone.

One is a default one. You cannot

delete or replace this game.

Reshape and Push:

Game instructions appear when

you select the game.

Select sound effects from the menu

item Options.

The second game may not have

been downloaded in your phone; if

not, you can download it by choos-

ing it from the Catalogue menu.

You can replace the second game

by another one from the catalogue

as many times as you want. The

Catalogue allows you to get the list

and description of the games you

can download. If the contents of

the catalogue is not available on the

phone it can also be downloaded.

All information related to games

downloading is available in the In-

structions menu.

To select a game:

Press . Select Games.

Choose the game (Push or

Reshape) and press Select

When in the game,

Item

Action

Play

Select Play to

start the game

(from the lowest

level).

Help

Select Help for

instructions and

controls.

Code

If you have

already played

the game and

reached a certain

skill level, select

Code to enter the

level code and

play the game

from that level.

The Trium 110 p games menu is

made of the following sub-men-

us: Catalogue, News, Settings

and Instructions in addition to

the available game(s) name(s).

This phone version does not bear the Reshape and

Push games.

Reshape and Push have skill levels.

When you win a level, you go to the

next level. After successfully playing

'X' number of levels the game gives

you a code to enable you to re-enter

the game from your previously at-

tained skill level. The game can

record player names and scores. If

you receive a call while playing, an-

swer in the normal way. To exit

from the games menu press Exit

Select one of the two first

options.

Item

Action

Select Catalogue

to see and/or

download games

available on the

network.

In our example: either Dollar-

>Yen or Yen->Dollar.

Enter the amount to be con-

Catalogue

verted. Press

to insert a

comma, if needed. Press

OK . The converted amount

appears.

Select News to

get information

on new games

availability.

Press and hold Exit

News

to return to the stand-by dis-

play.

Select Settings to

access the sound,

backlight... set-

tings common to

all games.

Select Instruc-

tions for all infor-

Conversion from one Euroland currency to another,

or to non-Euroland currencies, normally follows

"triangulation" rules (i.e. conversion of local cur-

rency to Euro and then Euro to other local cur-

rency). Your Currency-converter does not provide

this possibility. Accordingly, your result is only a

close approximation.

Settings

Instructions mation related to

games download-

ing.

Internet/Wireless Application

Protocol (WAP™)

Receiving an incoming call while playing may not

allow you to resume the current game.

Your phone has

WAP™ internet

browser to access services, such as

stock buying, news, sports, weather, TV

listings etc., supplied by your operator

and/or your internet provider. The

types of services offered depend

on the internet provider and net-

work operator.

You must have a DATA subscription to

access these services.

Either your phone is pre-programmed

with the settings or you must enter

them.

Currency-converter

To use the converter, set the curren-

cies and the exchange rate:

Press . Select Currency.

Select Settings.

Enter the first currency name

(e.g. Dollar). Press OK

Enter the second currency

name (e.g. Yen). Press OK

Enter the exchange rate using

to enter a comma.

Press OK

to validate the

See below to enter the settings. If you

cannot access the settings, they are pre-

programmed.

entry.

Press and hold Exit

to return to the stand-by dis-

play.

Access to the connection settings depend upon

whether the settings have been pre-programmed

prior to shipment from the factory. In some cases

and to avoid errors these settings are 'locked' and

are not user programmable.

To use your Currency-converter as a Euro converter

for participating currencies in the European Mone-

tary Union (“Euroland currencies”), please enter

the complete Euro exchange rate with six signifi-

cant figures. For example: 1 Euro = £ 0.61871.

Storing/editing connection settings

(operator provided)

You can enter up to 5 different pro-

To calculate the conversion be-

tween the chosen currencies:

Press . Select Currency.

files.

To enter and store the profile de-

tails:

Option

Action

Clears the memo-

ry used to store

information that

Press . Select Internet.

Select Profile list.

Select an empty profile ([...])

Clear cache you downloaded.

To clear this mem-

ory, select the Yes

option.

and press Options

Select Edit.

Enter the 4 digit phone lock

code (default code 0000) and

press OK

Select the Off op-

tion to reject pic-

ture

Enter all settings (the settings

Download

downloading.

pictures

depend on your operator).

This decreases the

page download-

ing time.

To activate the required pro-

file, use or

to select it

from the displayed list.

Used to allow or

Press Options

Select to validate.

and select

forbid the execu-

Scripting

tion of scripts

Press and hold Exit

within a page.

to return to the stand-by dis-

play.

Disconnects the

mobile from the

internet after a

1. You can also access the Internet menu directly by

pressing the Internet softkey from the stand-by dis-

play (provided you have not personalised the left

softkey).

2.If the phone number, login names and pass-

word, Home page http address and IP address are

not predefined, get these from your network opera-

tor and/or internet provider.

set period of inac-

tivity. Enter the

Auto-

period (0 - 60

disconnect

minutes) and

press OK

0 deactivates the

auto-disconnect

function.

Personalising your connection set-

tings

Optimise the behaviour of your

phone while connected to the inter-

net with the following settings:

Press and hold Exit

to return to the stand-by dis-

play.

Going online

To go online:

Press . Select Internet.

Select Settings.

Scroll to the following items

and turn on or off as

required:

Press . Select Internet.

Select Home page.

Connecting to followed by

your proxy name appears.

Then the word Loading... (of

the home page) appears.

Once connected, your provider spe-

cific menu options appear. The

icon indicates a 'live' circuit connec-

tion. By default the connection is

not secure.

To have a secure connection, set

’Security on’. The

icon indicates

a 'live' secure circuit connection.

Press . Select Internet.

Select Bookmarks.

Press Options , select Mod-

ify and enter the following:

Using

Press

while online

while online presents the

following options:

Item

Action

Returns to the

Increases or de-

creases the dis-

played text size

Adds a current

card to the list of

bookmarks

Goes to a book-

mark

Reloads the cur-

rent page

Option

Alias

Action

Name you wish to

give to your book-

mark

Back

Zoom +/-

Add book-

Address

Press OK

Home page address

to validate each

entry.

marks

Press and hold Exit

to return to the stand-by dis-

play.

Go to

bookmarks

During a live connection while

viewing page:

Reload

Press

options menu.

to display the

Reloads the home

page

Enter a different

site

Home page

Other Site

Select Add bookmark, enter

the Alias name and press

Disconnects the

browser from the

network but

leaves the current

page locally active

Bookmarks can only be Edited or Deleted from the

Bookmarks item under the Internet menu options

while offline.

Disconnect

Using bookmarks

Bookmarks can be used from the

stand-by display or while browsing.

• Directly from the stand-by dis-

play:

Disconnects the

Close session phone from the

internet

The appearance of these items de-

pends on the operator and/or val-

ues in the Settings menu.

Press . Select Internet.

Select Bookmarks.

Select the bookmark name

you require.

Ending the online connection

To end the online connection:

To access the Internet directly use the Internet soft-

key (if not personalised).

Press

You can also select Close session item under the

options menu.

• While browsing the internet:

Press

to display the

Creating bookmarks

options menu.

To revisit specific cards more quick-

ly, use bookmarks to store the card

address. This function depends on

your provider. You can create a

maximum of 10 bookmarks. Create

bookmarks from the stand-by dis-

play or while viewing a page.

Select Go to bookmarks.

Select the bookmark name

you require.

Other site

You can enter another internet ad-

dress directly by using the Other

site option from the Internet

menu. Addresses are not stored and

must be entered each time.

GSM man machine interface

codes

The phone supports the standard

GSM key sequences using the * and

# characters sent directly from the

keypad to the network. These se-

quences are used to activate all the

supplementary services provided by

the network. Consult your service

provider for a complete list.

Accessories

Using the headset

Connecting the headset

Insert the headset plug in the

phone headset connector as

shown:

While inserting the headset plug in the phone

headset connector make sure the Trium logo

(

) appears on top. Otherwise the headset

does not work properly.

Using the headset

Place the headset earpiece in your

ear.

Earpiece

The headset microphone is then

at a convenient level for

operation.

Microphone

You can answer, reject and end

calls using

Adjust the earpiece volume level

using or

(see page 11).

Disconnecting the headset

Tilt the headset plug down as

shown:

Appendix

Expression

PIN/PIN2

PPP

Meaning

Personal Identification

Number. Supplied by

your network/service

provider

Point to Point Protocol

PIN Unblocking Key.

Used to unlock PIN and

PIN2. Supplied by your

network/service provid-

Glossary

Expression

Meaning

Alternating Current/Di-

rect Current charger

The call currently in con-

versation

AC/DC charger

Active call

ALS

PUK/PUK2

Alternate Line (Line 2)

Service

Advise of Charge - sub-

scription service

Cell Broadcast

AoC

The ability to use your

Roaming (Rm) telephone at home or

abroad.

Caller Line Identity - dis-

plays callers telephone

number

Service Dialling

CLI

SDN

Number. Of your opera-

tor or service provider

Subscriber Identity

Module. Supplied by

your network/service

provider

Short Message Service

Service Provider Name

Status Report - relates

to SMS messages

When the phone is on,

registered onto a net-

work but not making or

receiving a call

Uniform Resource Loca-

tor

Wireless Application En-

vironment

Wireless Application

Protocol

Wireless Session Proto-

col

Conversation

mode

When the phone is mak-

ing or receiving a call

Data Encryption stand-

ard

SIM

DES

Divertsincomingcallsto

the phone to another

number

SMS

SPN

Diverting

DTC

EMS

Desk Top Charger

Enhanced Message

Service

Stand-by mode

Dual Tone Multifre-

quency Tones

DTMF

FDN

Fixed Dialling Number

Global System for Mo-

bile communications

HyperText Transfer Pro-

tocol

URL

GSM

WAE

WAP™

WSP

WTP

http

InformationNumbersof

your operator

LCD

MMI

Internet Protocol

Liquid Crystal Display

Man machine Interface

Wireless Transport Pro-

tocol

Trouble shooting

Possible cause and so-

lution

Problem

Possible cause and solu-

Fixed Dialled Number or

Call Barring features are

turned on. Check features

and turn them off (see

pages 25 and 42).

Problem

Stored tele-

phone num-

bers cannot

be recalled

tion

Check that the battery is

fully charged and correctly

connected to the phone.

There may be no mains

supply. Try a different elec-

trical socket.

The AC/DC charger may be

faulty. Return to your deal-

er and try substitution

with another Mitsubishi

adaptor. If faulty contact

your dealer.

Cell broadcast is perma-

nently on, using more bat-

tery power.

Phone is in a poor signal

area and therefore always

on full power.

Phonewillnot

switch on

Phone

Display contrast is turned

down too low. Reset con-

trast (see page 34).

switches on

but there is

no display

No flashing

battery icon

while charg-

ing

May indicate a charging

or battery problem. Turn

the charger off and dis-

connect it. Reconnect and

try again.

May also indicate the bat-

tery is full and does not

need more charging.

Battery icon

not flash-

ing 1-2-3

during charg-

ing

There is not enough mem-

ory to store another SMS

message. You must delete

one or more of the exist-

ing stored messages (see

page 26).

Short stand-

by and talk

times

Incorrect charging and dis-

charging. Always charge

and discharge your battery

fully.

Flashing

The battery is wearing out.

Replace the battery.

Numbers can- Keypad lock is on ( ap-

Function no longer availa-

ble in the SIM or was sub-

scription dependent.

Reprogram the softkey

(see page 34).

(......)

softkey

not be en-

tered

pears). Press Unlock

and to turn off.

Check at least one signal

strength bar ( ) is dis-

played. Try a stronger sig-

nal strength area.

If no network name is dis-

played, check registration

and area coverage with

your service/network pro-

vider and check the SIM is

correctly inserted.

Calls cannot

be made or

received

Call barring option is on.

Deactivateit(seepage 42).

Call cost limit is reached

(see page 31).

Error messages

Possible cause and

solution

Problem

Possible cause and

You have made a re-

Cannot exe- quest which is impossi-

Problem

solution

You are trying to place

an outgoing call and the

allowed credit is already

cute com-

mand

ble to be executed in

the current call situa-

tion.

Allowed cred- reached.

it reached! The allowed credit limit

The short message text

cannot be displayed

(characters not recog-

nised, incorrect format

etc.)

Can't display

message

is reached during an

outgoing call (the call is

then aborted).

You are trying to make a

call and the call fails be-

cause the destination

number is already en-

gaged in conversation.

There is no SIM present

or the SIM is incorrectly

inserted. See page 10

for more details.

Check SIM!

Busy

You changed the call

barring password or

You changed the call

barring service status.

The entered password

seems to be wrong or

incorrect.

The user is unreachable.

The outgoing call fails

due to:

the network cannot

take the call due to sys-

tem busy or

the number is out of or-

der or

the number is unreacha-

ble or

the network does not

answer or

the option to hide your

phone number when

calling is not supported

by the network

Check your

password

You made a request for

a service that seems to

be impossible to fulfil.

Check your

request

Call failed

You tried to activate a

GSM service. You are re-

quested to check your

Check your

subscription subscription regarding

the related service

rights of use/access.

The network cannot

perform your request

and generates an error

result.

Control the ability to

hide your ID when mak-

ing a call (service availa-

bility in network).

Error!

An SMS sending process

Cell broadcast activa-

Failed

failed (the short mes-

sage cannot be sent).

Cancelled. No tion has been requested

type selected but no message type

has been selected.

You entered a character

string with a syntax er-

ror.

Incorrect en-

try

Possible cause and

solution

Possible cause and

solution

Problem

You tried to make a call

and the call is rejected

by the network be-

cause the network

does not recognise the

phone number struc-

ture or

you tried to store a

phone number that is

too long to be stored in

the selected location or

you tried to move a

phone entry to a loca-

tion that is unable to

receive the phone

When a copy/move op-

eration is made on

No action per- memories but no con-

formed

ditions have been

changed (same memo-

ry, number and name).

You made a call to a re-

mote user and no re-

sponse has been

Invalid

number

No response

Not allowed

received.

Your number/charac-

ter entry is not allowed.

A call is tried, but can-

celled due to fixed dial-

ling control (the

number dialled does

not match with one of

the fixed dialling num-

bers in memory).

There is no more SIM

storage.

The called number has

changed.

A wrong PIN code has

been entered 3 times.

A wrong PIN2 code has

been entered 3 times.

A wrong PUK2 code

has been entered 10

times.

Not allowed

(fixed dial-

ling)

number (phone

number too long)

Keypad locked A press on any key is

"Unlock" # to made with keypad

unlock

locked.

This text appears when

the battery becomes

Not Available

Number

changed

Low battery! too low and the mobile

soon switches off auto-

matically.

PIN blocked

You tried to make a

call. The call is rejected

by the network due to

congestion problems.

PIN2 blocked

Network busy

When selecting net-

work manual search,

Network not

PUK2 blocked The SIM services pro-

tected by the PIN2 code

have now been perma-

nently disabled.

you have selected a

allowed

network that rejects

the connection.

New PIN in-

correct. Try

again

Changing PIN: the new

PIN code values differ

(value control).

Ring volume

Off

The ring volume is set

to 0 (no volume)

The cost limit is about

to be reached. The con-

nected call ends auto-

matically when the

limit is reached.

New PIN2 in- Changing PIN2: the

correct. Try

again

new PIN2 code values

differ (value control).

Reaching al-

lowed credit!

Possible cause and

solution

Possible cause and

solution

Problem

Activating some GSM

services that are not

available on the net-

work

An unrecoverable error

has occurred. Switch

the handset off and

back on again. It may

be necessary to reset

the EMS system (Set-

tings menu). Beware:

all services and EMS

messages will then be

erased.

Service not

available

A wrong PUK has been

entered 10 times.

The SIM card has been

permanently disabled

and needs to be re-

placed by a new one.

Internal fault

SIM blocked.

Contact pro-

vider

An invalid service menu

has been sent to the

Invalid Serv- handset. The invalid

A wrong PIN code has

SIM blocked. been entered 3 times.

Enter PUK:

Enter the PUK code to

unblock the SIM card.

ice Menu

service menu is ig-

nored, no further ac-

tion necessary.

SIM fixed full

SIM names

full

Phone names

full

The corresponding

memory is full.

You have not regis-

tered to any service. Go

to the Service registra-

tion menu.

Registration

required

The storage of new

messages (when writ-

ing a new SMS) is im-

possible.

SMS memory

locations are

full

A new service menu

item has been received

but the remaining stor-

age space is not suffi-

cient to store it. Delete

one or more registered

menu items (My Servic-

es menu) and accept

the new menu or dis-

card the new menu.

Wrong code. A wrong phone lock

Menu limit

reached

Try again

code has been entered.

Wrong new

code. Try

again

The new phone lock

codes do not match

(value control).

Wrong PIN,

try again

Wrong PIN2,

try again

Wrong PUK,

try again

Wrong PUK2,

try again

A new service has been

received but the re-

maining storage space

is not sufficient to store

it. Delete one or more

registered service(s) -

Settings menu - and ac-

cept the new service or

discard the new serv-

ice.

The wrong code has

been entered.

Server limit

reached

The handset may be

out of the network

range or the network is

temporarily overload-

ed.

Message not

sent

number, together with the service card. Fi-

nal determination of guarantee claim eligi-

bility shall be made by MITSUBISHI.

MITSUBISHI shall not be liable for ship-

ment costs to and from an authorised GSM

MITSUBISHI service centre; the product

travels at your risk.

Guarantee

Pan European Service

Should you experience any difficulty then

please contact your nearest MITSUBISHI

location listed below for information on

other service centres.

4.This guarantee does not cover:

a)battery defects of any nature;

UNITED KINGDOM

ESPAÑA

b)non-compliance with directions for use;

c)installation or removal charges where

the product is installed in a vehicle;

d)defects or failures caused by accident,

misuse, improper installation or improp-

er repair by an unauthorized repairer, al-

teration or modification, neglect, failure

to use for normal purpose, Acts of God,

water ingress, use in adverse environ-

mental conditions (humidity or tempera-

ture);

Tel: (0800) 912 00 20

Tel: (902) 11 68 58

FRANCE

Tel: (0825) 86 82 83

ITALIA

Tel: (800) 27 59 02

DEUTSCHLAND

Tel: (01803) 33 71 84

IRELAND

Tel: (1800) 92 70 12

BELGIUM

Tel: (0800) 75733

SWITZERLAND

Tel: 032 843 65 11

AUSTRIA

Tel: (0800) 292716

FINLAND

Tel: (0800) 116 975

PORTUGAL

SWEDEN

e)cost of or performance of modifications

to product to adapt or adjust to conform

to national or local safety laws, where

such safety laws go beyond harmonised

European Union standards;

f)loss of use of the product or consequen-

tial loss of any nature;

g)loss of use of air-time, loss of use of any

loaned equipment or ancillary equip-

ment;

h)provision of incorrect or insufficient sig-

nal on air-time network, upgrading of

product software to changes in network

operating parameters, mains supply

voltage fluctuations, incorrect SIM card

(memory card) parameters for connec-

tion to airtime retailer;

Tel: (0800) 880 264

Tel: (0200) 214 715

THE NETHERLANDS

Tel: (0800) 0223825

To obtain Warranty Service, you will re-

quire your original equipment purchase

invoice or irrefutable proof of purchase.

Please see warranty terms and conditions

for in warranty service.

Pan-european GSM End-user Guar-

antee Conditions

1.You can benefit from this guarantee only if

you are the original end-user purchaser.

2.MITSUBISHI guarantees that for a period of

twelve (12) months from the date of pur-

chase from your dealer, the Product shall

be free from defects in materials and work-

manship. Subject to the conditions below,

Mitsubishi will indemnify you against all

cost of parts and labour for repairs to or re-

placement of the product or parts (which

may include equipment of similar type)

where conducted by an authorised MIT-

SUBISHI GSM service centre. MITSUBISHI

shall be entitled to retain product which

has been replaced.

i)damage caused by non-MITSUBISHI ac-

cessories.

5.Any guarantee claim or service does not

extend the original guarantee period un-

less so required by prevailing national law.

6.This guarantee is valid only if the product

is purchased and used in the European Un-

ion, Norway, Iceland or Switzerland.

THIS GUARANTEE DOES NOT AFFECT YOUR

STATUTORY RIGHTS.

3.Any claims must be made to an authorised

MITSUBISHI GSM service centre in the

countries mentioned in the service card en-

closed with the product. In case of difficul-

ty you can contact the Mitsubishi

companies listed in the service card to ob-

tain details of your nearest authorised MIT-

SUBISHI GSM service centre. As a condition

of this guarantee, the date of your pur-

chase must be confirmed by producing

your original invoice from your supplier or

your sales receipt, showing the serial

DECLARATION OF COMPLIANCE

Name

: Mitsubishi Electric Telecom Europe S.A.

RCS Nanterre B 307 593 129

: 25, boulevard des Bouvets

: Nanterre Cedex

Address

Town

Postal code

: 92741

Identification of the product

Nature

Type

Sales reference

: Mobile Cell Telephone

: Dual band GSM 900/DCS 1800

: MT-360

Declares under its entire responsibility that the product described above complies with the

following basic applicable requirements (and in particular those in the 1999/5/CE directive):

Article 3.1a: (health protection and user safety)

_73/23/CD_EEe_{, C}c_el_na_eler_ca_Et_Ni₅o₀₃n₆₁of compliance

Article 3.1b: (protection requirements concerning electromagnetic compatibility)

89/336/CEE, ETS 300 342-1

Article 3.2: (proper use of the radio-electric spectrum so as to avoid damaging interference)

EN 301 511

To this effect, declares that all the radio test series have been carried out.

of January 2002,

Viet Mailam

Managing Director

Index

Access to the menus ................. 20

Alarm

Cache memory

Clearing .............................. 48

Emergency calls ........................... 5

EMS ........................................... 29

Ending a call .............................. 12

Error messages .......................... 54

Clock .................................. 44

Alert mode ................................ 32

Alert tone

Turning on/off .................... 26

Any key answer ......................... 34

Auto

Answer ............................... 35

Retry .................................. 35

Auto-disconnect ........................ 48

Automatic ramping ................... 33

Automatic search ...................... 41

Auto-switch ............................... 45

Calculator .................................. 45

Call

Conference ......................... 19

Duration ............................. 31

Holding .............................. 18

Multi-party ......................... 19

Reminder ........................... 31

Retrieving ........................... 18

Times ................................. 30

Waiting .............................. 18

Call barring ............................... 42

Password .............................. 7

Call costs

FDN ........................................... 25

Fixed dialling numbers .............. 25

General

Safety ................................... 4

Getting started .......................... 10

Glossary ..................................... 52

GSM man machine

interface codes ...................... 50

GSM Services ............................. 38

Call barring .................. 42, 43

Call diverting ...................... 39

Network ....................... 40, 41

Receiving caller ID .............. 40

Sending my ID .................... 40

Reset .................................. 32

Call timer

Backlight ............................. 15, 34

Balance information .................. 30

Barring password

Reset .................................. 31

Caller line identity ..................... 39

Calling ....................................... 11

Calls & Times ............................. 29

Call costs ...................... 31, 32

Call timers .................... 30, 31

Calls log ............................. 29

Costs .................................. 31

Line selection ..................... 32

Calls Log .................................... 29

Care and maintenance ................ 5

CB ............................................. 43

CB messages

Deleting ............................. 44

Editing ............................... 44

Reading .............................. 43

Cell broadcast ........................... 43

CLI ............................................. 39

Conference call .......................... 19

Connection profile ..................... 47

Cost management ..................... 31

Country Codes ........................... 16

Creating a draft text .................. 27

Credit limit ................................ 31

Currency-converter .................... 47

Call ..................................... 42

Basic operations

SMS ................................... 15

Unanswered call ................. 15

Voice mail .......................... 15

Battery ...................................... 10

Alarm volume .................... 33

Charging ............................ 12

Handsfree features .................... 17

Headset

Use ..................................... 51

Holding a call ............................ 18

Disposal ...............................

Fitting ................................ 12

Low battery warning .......... 12

Removing ........................... 12

Incoming Calls

Diverting ............................ 39

International Country Codes ...... 16

Internet ............................... 15, 47

Bookmarks ......................... 49

Going online ...................... 48

Home page ........................ 48

Other site ........................... 49

Personalising ...................... 48

Profile list ........................... 48

Settings ........................ 47, 48

Safety information ...............

Use .......................................

Battery cover

Replacing ........................... 10

Bookmarks

Creating ............................. 49

Deleting ............................. 49

Using ................................. 49

Broadcast .................................. 43

Alert ................................... 44

Language ........................... 44

Message types ............. 43, 44

On/Off ................................ 43

Keypad lock ......................... 15, 32

Language selection .................... 32

Last dialled numbers ................. 16

Line 1 ................ 25, 29, 30, 32, 39

Line 2 .......... 25, 29, 30, 32, 38, 39

Date setting ............................... 37

Default settings ......................... 37

Dialling

Calls Log memory ............... 16

Phonebook ......................... 16

Dialling from memory ............... 16

Display contrast ......................... 34

Diverting ................................... 39

Draft text

Creating ............................. 27

Editing ............................... 27

DTMF tones ............................... 17

Making a call ............................. 11

Managing SMS messages .......... 26

Melodies ................................... 33

Melody download ..................... 38

Menu ........................................ 20

Access ................................ 20

Menu graphics .......................... 34

Menu map ................................ 20

Message templates ................... 28

Messages ............................ 15, 26

Alert ................................... 26

Draft texts .......................... 27

Inbox .................................. 26

Msg. Templates .................. 28

Outbox ............................... 28

Rich Messages .................... 29

Settings .............................. 26

Storage .............................. 29

Write new .................... 27, 28

Mobile number

Ramping .................................... 33

Reading an SMS message .... 26, 29

Receiving a call .......................... 12

Reminder - call time .................. 31

Responsibility .............................. 6

Retrieving a call ......................... 18

Ring ........................................... 33

Ring tone .................................. 33

T9 .............................................. 20

T9 text entry .............................. 21

Time & date ............................... 37

Time settings ............................. 37

Trouble shooting ....................... 53

Turning

Off ..................................... 12

On ...................................... 10

Safety information ...................... 4

Battery ................................. 6

Care and maintenance ......... 4

Emergency calls .................... 4

Responsibility ....................... 4

Security codes ...................... 4

Vehicle safety ....................... 4

Scratchpad ................................ 44

Scripting .................................... 48

Second call ................................ 19

Security ..................................... 35

Codes ................................... 6

Features ............................. 35

Sending an SMS message .......... 27

Settings ..................................... 32

Auto features ..................... 35

Broadcast ..................... 43, 44

Default settings .................. 37

Display ............................... 34

GSM Services 39, 40, 41, 42, 43

Internet .............................. 47

Keypad lock ........................ 15

Keys ............................. 34, 35

Language ........................... 32

Menu graphics ................... 34

Phone settings ....... 15, 32, 33

34, 35, 36, 37

Vehicle safety .............................. 4

Vibrate ...................................... 33

Vibrate & ring ............................ 33

Vibrate alert modes ................... 17

Vibrate then ring ....................... 33

Voice Mail

Alert ................................... 38

Call ..................................... 38

Number .............................. 38

Voice mail ................................. 38

Volume ...................................... 17

Adjustment ........................ 17

Alert mode ......................... 33

Conversation ...................... 33

Keys tones .......................... 33

Ring tone ........................... 33

Hiding ................................ 39

Showing ............................. 39

Multi-party call .......................... 19

Muting ...................................... 17

Network .................................... 40

Network services ....................... 22

WAP™ ....................................... 47

Office Tools

Alarm clock ........................ 45

Scratchpad ......................... 44

Office tools ................................ 44

Online connection ..................... 48

Bookmarks ......................... 49

Ending ............................... 49

Personalising ...................... 48

Outbox ...................................... 28

Own number ............................. 25

Security ........................ 36, 37

Time & date ........................ 37

Tones ..................... 32, 33, 34

Voice Mail .......................... 38

Show costs ................................ 32

Silent ......................................... 33

Silent alert mode ....................... 17

SIM

Pause feature ............................ 18

Phone

Customising ....................... 32

Phone Book

Calling numbers ................. 24

Fixed Dialling ..................... 25

Free space .......................... 24

Own numbers .................... 25

Recall ................................. 24

Remaining .......................... 24

Store ............................ 23, 24

Viewing numbers ............... 24

Phone lock ................................ 36

Code .............................. 7, 36

Phone settings .......................... 32

Phonebook ................................ 22

PIN code .................................... 36

Card ................................... 10

SIM card .................................... 14

SMS ..................................... 15, 26

SMS messages

Managing .......................... 26

Preparing your phone ........ 26

Reading ........................ 26, 29

Sending .............................. 27

Storing ............................... 28

Softkey programming ............... 34

Solutions ................. 53, 54, 55, 56

Speed dialling ...................... 16, 35

Standby display ......................... 11

Storage consumption ................ 29

Storing an SMS message ........... 28

Storing names and numbers ..... 22

PIN/PIN2 codes ............................

PIN2 code .................................. 36

Problems ....................... 54, 55, 56

Programmable

Softkeys ............................. 34

Speed dialling .................... 16

PUK code ................................... 37

PUK/PUK2 Codes .........................

PUK2 code ................................. 37

Austria

0800 292716

Germany

0800 1808133

Netherlands

0800 0223825

Belgium

0800 75733

Greece

00800 44131247

Portugal

0800 880264

Denmark

8088 1816

Ireland

1800 927012

Spain

9009 34497

Finland

0800 116975

Italy

800 791029

Sweden

0200 214715

France

0800 913080

Luxembourg

800 23 552

0800 9120020

www.mitsubishi-telecom.com

FA9M078910-A

NETGEAR ReadyNAS 3200 User Manual
Motorola W372 User Manual
LG Electronics TM510 User Manual
JVC KD R600 User Manual
JVC GR DVL145 User Manual
Echo Bear Cat SC3206 User Manual
Dynex DX ECOD1 User Manual
DeLonghi EAM3400 User Manual
Classe Audio CDP 100 User Manual
Brinkmann 844 0350 0 User Manual